What is the role of shielding gas in a Plasma Powder Surfacing Machine?

Nov 17, 2026Leave a message

If you’ve ever watched a Plasma Powder Surfacing Machine operate, you might have noticed a thin, steady stream of gas flowing around the bright, blazing plasma arc—especially if you’re working with precision parts like extruder screws, valve seats, or turbine blades. At first glance, it might seem like a trivial detail, but anyone who’s spent time troubleshooting or perfecting a surfacing job will tell you: the shielding gas is one of the most critical, and most misunderstood, components of the entire process. As a supplier of these machines, I’ve seen firsthand how even the smallest adjustment to shielding gas flow, purity, or type can make the difference between a perfectly hard, defect-free coating and a part that’s riddled with cracks, porosity, or weak adhesion. Let’s break down exactly what shielding gas does in Plasma Powder Surfacing (often called PTA surfacing, for short) and why it’s non-negotiable for consistent, high-quality results.

First, let’s ground ourselves in the basics of how a Plasma Powder Surfacing Machine works, just to set the context. The core of the process is a plasma arc: we take a gas (usually argon) ionize it with a high-voltage electrical charge to create a superheated plasma plume that can reach temperatures of 10,000–20,000°C. This plasma melts a stream of powdered hardfacing material (like tungsten carbide or cobalt-chromium alloys) which is then deposited onto a prepared metal part, creating a tough, wear-resistant coating. It’s a precise process, which is why our equipment—including specialized units like the Extruder Screw PTA Hardfacing Machine, Valve Seat PTA Hardfacing Machine, and Power Turbine Blade Hardfacing Machine—are designed to control every variable: arc heat, powder feed rate, and, of course, gas flow. But here’s the catch: that superhot plasma is incredibly reactive. If it’s exposed to oxygen, nitrogen, or moisture from the air mid-deposit, those gases will contaminate the molten powder and the base material, ruining the coating. That’s where shielding gas steps in.

The primary job of shielding gas is to create a protective barrier between the molten weld pool (the mixture of melted base material and hardfacing powder) and the atmosphere. Let’s be clear: when you’re working with a PTA Welder, the molten pool is liquid metal at nearly 2,000°C. At that temperature, even trace amounts of oxygen will react with the metal, forming oxides that are brittle and weak—think of the rust that forms on a steel tool left out in the rain, but at a much faster rate. Nitrogen will also dissolve into the molten metal, creating porosity (small air pockets) that weaken the coating and make it prone to cracking under stress. Even moisture in the air can break down at high temperatures, releasing hydrogen that causes hydrogen-induced cracking, a common headache for hardfacing jobs. So shielding gas isn’t just “helping”—it’s the only thing keeping that molten pool from reacting with the air long enough to solidify into a strong, uniform coating.

But shielding gas does more than just block the atmosphere. It also shapes and stabilizes the plasma arc itself. The plasma arc is constricted by a ceramic nozzle at the end of the PTA torch, and the shielding gas flows through and around this nozzle, helping to focus the arc into a tight, consistent plume. A well-shielded arc is narrower and more concentrated, which means the heat is directed exactly where we want it—on the part and the powder, not wasted heating the surrounding air. That’s especially important for precision parts, like the cutting edges of an extruder screw or the sealing surfaces of a valve seat, where too much heat can warp the part or damage nearby components. In our Power Turbine Blade Hardfacing Machine, for example, the blades are delicate, high-value components where even a 0.1mm warp can make the part unusable. The right shielding gas flow keeps the arc focused, so we only heat the small area we’re coating, preserving the blade’s original dimensions and material properties.

Another key role of shielding gas is controlling the metallurgy of the final coating. Different types of shielding gas (or mixtures) have different thermal properties and reactivity, which let us tailor the coating’s hardness, toughness, and resistance to wear or corrosion. For example, pure argon is the most common shielding gas for PTA surfacing because it’s inert (it won’t react with most metals) and has good arc-stabilizing properties. But sometimes, we use mixtures: adding a small amount of hydrogen to argon can increase the arc’s heat, making it easier to melt hard, high-melting-point powders like tungsten carbide. This is especially useful when surfacing parts that need extremely hard coatings, like industrial pump impellers or drilling tools. Conversely, adding a bit of carbon dioxide can help reduce spatter (those tiny, unwanted molten metal droplets that stick to the part) in some applications, though we have to be careful not to add too much, as CO2 can react with metal at high temperatures to form oxides.

It’s not just the type of gas that matters—flow rate is critical too. Too little shielding gas, and the protective barrier is weak; air will seep in, causing porosity and oxide inclusions. I’ve seen this firsthand when a customer called us because their valve seat coatings kept failing quality tests. When we checked their machine, we found their shielding gas flow was set 30% lower than our recommended settings for the Valve Seat PTA Hardfacing Machine. Once we adjusted it, the porosity in their coatings dropped from 15% to less than 1%, and their scrap rate fell by 20%. Too much shielding gas, though, can create other problems: excessive flow can disrupt the plasma arc, causing it to waver or become unstable, which leads to uneven coating thickness. It can also blow the molten powder away from the target area, wasting expensive hardfacing material and creating an inconsistent coating. So finding the right flow rate is a balance, and it’s one of the first things we walk customers through when they set up their new PTA equipment.

Plasma Powder Surfacing MachinePower Turbine Blade Hardfacing Machine factory

Now, let’s talk about common mistakes that people make with shielding gas, because that’s where a lot of avoidable problems come from. One big one is using low-purity gas. If your shielding gas has even 0.1% oxygen or moisture, that’s enough to contaminate a molten metal pool. We always recommend using ultra-high-purity argon (99.998% or higher) for PTA surfacing—any lower, and you’re asking for trouble. Another mistake is not purging the lines or the torch before starting a weld. Even if you have good gas purity, if there’s air trapped in the hoses or the torch nozzle, that air will get into the weld pool when you strike the arc. That’s why we always advise customers to run the shielding gas for 10–15 seconds before turning on the plasma power, to flush out any trapped air. And for parts that require more than one layer of coating, it’s important to continue the shielding gas until every layer has solidified—don’t cut it off as soon as the first layer is done, because that second layer is molten too and will still be vulnerable to contamination.

As a supplier of Plasma Powder Surfacing Machine, I can’t stress enough how integral shielding gas is to the process. It’s not a afterthought or a setting you can tweak once and forget—its quality, type, and flow rate are core to getting a coating that meets your performance requirements, whether that’s resistance to abrasion for an extruder screw, high-temperature strength for a turbine blade, or tight sealing for a valve seat. We’ve designed all our equipment, from the basic PTA Welder to specialized hardfacing units for specific parts, with shielding gas control as a key feature. Our machines let you adjust gas flow, switch between gas types easily, and monitor gas purity in real time, so you can dial in the perfect settings for your application without guesswork.

If you’re in the market for a reliable Plasma Powder Surfacing Machine, or if you’re looking to upgrade your current setup to get better, more consistent coatings, I’d encourage you to reach out to our team. We’ve helped hundreds of businesses, from small machine shops to large industrial manufacturers, optimize their PTA processes, and we’re always happy to walk you through the ins and outs of shielding gas, arc stabilization, and powder feed rates. Don’t let a small detail like gas hold your surfacing jobs back—contact us today to learn more about how our equipment can help you get the high-quality, durable coatings your parts need.

References

  1. Kalpakjian, S., & Schmid, S. R. (2014). Manufacturing Processes for Engineering Materials (7th ed.). Pearson.
  2. Linnert, G. E. (1994). Welding Metallurgy: Volume 2, Processes and Products (2nd ed.). American Welding Society.
  3. Davis, J. R. (Ed.). (2001). Hardfacing, Weld Cladding, and Repair Fabrication. ASM International.
  4. Savage, W. F., Nippes, E. F., & Szekeres, E. S. (1975). Behavior of shielding gases in welding processes. Welding Journal, 54(10), 451-s to 460-s.